Ecu fooling for code 41
hey i keep on getting code 41 in my d16z6
the o2 heater thing how much volts does the o2 heater run on? is there a way to fool it? cause if dun got 1 layin around and its hard to find one near ma place so can u put summin else in the o2 heater circut instead of the o2 and trick it? i.e. put the power and ground on a bulb or summin sum one plz giv suggestions ez |
Re: Ecu fooling for code 41
Wire in a 1K ohm 1/4 watt resistor in place of the O2 heater. |
Re: Ecu fooling for code 41
aite thanks soo much
ill try that thanks again |
Re: Ecu fooling for code 41
btw
wut do u mean by "K" u mean a 1ohm resistor rite? |
Re: Ecu fooling for code 41
Would correctly spelling out a complete sentence be asking too much? 1k is 1000 ohms.
|
Re: Ecu fooling for code 41
sorry man if u didnt like my way of typing
is this ok now? :) so u say tat a 1kohm n a .25 watt resistor would work for this? and not giv me the cel again has any of you tried it? |
Re: Ecu fooling for code 41
whA tHE fUk R U AXn?
|
Re: Ecu fooling for code 41
wtf
any ways i tried a couple of used o2 sensors and cel still didnt go also tried the 1k .25ohm resistor thing and it didnt work either frum the 2 black wires only one is giving + some people are saying that the other is a ground wire and some are saying it should also giv a + current btw if i short both of em the cel goes away but the car start to die and turns off in a while its probably faulty wireing how do u re-wire a o2 sensor? i want to put new wires from the ecu so any help would b nice |
Re: Ecu fooling for code 41
damn niga
why are you typing as if it were a damn poem? |
Re: Ecu fooling for code 41
well you understand dont u
screw tat anybody willin to help? |
Re: Ecu fooling for code 41
no
|
Re: Ecu fooling for code 41
ok u got nothin to say then fuk off. someone else tell me how to re-wire all the o2 sensor wires (ecu till the sensor).
ez |
Re: Ecu fooling for code 41
anyone?
|
Re: Ecu fooling for code 41
fuk off dog
|
Re: Ecu fooling for code 41
what the ----. dont fukin make me rape u
|
Re: Ecu fooling for code 41
Go look at your manual. you can figure out how to wire them direct. I think the signal wire is D14, not sure though. Just seems that way in my memory.
|
Re: Ecu fooling for code 41
i was thinking of that, but wen i looked for my manual i couldnt find it. lol. anyone got a link to a cyber one?
|
Re: Ecu fooling for code 41
---- off, and rape me ::)
|
Re: Ecu fooling for code 41
i would suggest
you buy a new car and drive off a really high cliff anyone agree? |
Re: Ecu fooling for code 41
Originally Posted by yllwciv5
i would suggest
you buy a new car and drive off a really high cliff anyone agree? |
Re: Ecu fooling for code 41
you can disable the o2 heater circut when you edit the rom dog
|
Re: Ecu fooling for code 41
hooking up the wb to the d14 pin wont get rid of the code 41. you have to find a way to complete the circuit with the o2 heater, or just disable the o2 heater in uber/crome. idiot.
|
Re: Ecu fooling for code 41
Originally Posted by Foowee
you can disable the o2 heater circut when you edit the rom dog
|
All times are GMT -5. The time now is 12:38 AM. |
© 2024 MH Sub I, LLC dba Internet Brands