did it die?help
10-05-2006, 05:51 PM
#1
0.0 BAR
Thread Starter
Join Date: Sep 2006
Posts: 9
did it die?help
here is my setup n/a f22a1 91 accord with dsm 450s and po6 m/t chipped with uberdata i have one hell of a time getting a good tune and still am 3 days ago I unplugged my pcm and then plugged it back in the key was off of course and when i started it up and drove it I got a cel it was 1 long blink and 2 shorts which I read as code 3 map sensor. I wired in gm 3 bar map still same thing got a used honda map that works and tried it and cleared codes and still the code comes right back. if I attempt to burn a different map to the sst chip the cel just stays on and hits what seems like a rev limiter at like 4 grand and runs like ---- it does the same thing in chrome I have been running the stock gsr bin in uberdata with the map changed for 450s and it ran ok it actually had more power than it did before but not my power and torque sucks since the stupid cel happened I have good engine vacume i have plenty of gas in the tank my clutch doesn't slip or anthing like that my trans in is in good working order. I can only assume these reasons my po6 is a piece of ----,the sst chips are ---- and got fried somehow,uberdata is a piece of ---- or I am a complete dumb ***. all I know is I used to be able to roast the ---- of my tires and now when I get on it to leave a stop light it almost dies and takes forever to rev and has ---- for power please anyhelp or ideas would be great I am thinking of buying some new sst chips and another po6 and chip kit not sure but eversice I have chipped my po6 its been a real bitch. I am ussing the willem standard burner too. HELP btw I live in spokane so anyone who is close that can help me out would be cool too
10-05-2006, 07:34 PM
#2
Guest
Posts: n/a
Re: did it die?help
Well it sounds like you have a problem with your ecu chipping job. get another ecu and have it chipped by someone experianced like exenocron or moates.net.
to see if it's a bad chipping job cut J1 and see if it will rev past 4grand. It'll run all weird because the ecu is stock for a d15 oe some ----. but it will rev out then you know it's a bad chipping job.
to see if it's a bad chipping job cut J1 and see if it will rev past 4grand. It'll run all weird because the ecu is stock for a d15 oe some ----. but it will rev out then you know it's a bad chipping job.
10-06-2006, 03:23 PM
#3
3.0 BAR
Join Date: Jul 2003
Posts: 6,449
Re: did it die?help
Originally Posted by 91cb7accord
I can only assume these reasons my po6 is a piece of ----,the sst chips are ---- and got fried somehow,uberdata is a piece of ---- or I am a complete dumb ***.
2 - nope
3 - yep
4 - umm...
1 long blink followed immediately by 2 shorts is 12
3 short blinks would be MAP
10-06-2006, 11:37 PM
#4
0.0 BAR
Thread Starter
Join Date: Sep 2006
Posts: 9
Re: did it die?help
then that code would be an egr code and I don't see how egr could cause a problem with drivability about 3k it would run like ---- at idle with egr stuck open but other that I don't see how that would cause my problems unless egr and map signals are linked together.
Thread
Thread Starter
Forum
Replies
Last Post
turbo4life
Forced Induction
23
08-09-2008 06:09 PM
