chipped my ECU ..Problems...!!!!
I tried using the .bin that Chevy wrote for me and it wont go past 3,500 RPM's. I tried the one i made and it wouldnt go past 4,000 k. I did notice thought that when i held the gas and it would just stop at 4,000 it would blow off abit when i let off the gas.
Anyway, i also noticed that when the ECU case touched the metal on the car ( the mouting area where the ECU sits ) it would cut off. Like somethin isnt grounded within the ECU. I can't seem to figure it out. I dont know whats causing the short and i'm thinking that this is why it wont rev past 4,000k. anyone ever have this problem. |
Re:chipped my ECU ..Problems...!!!!
what ECU?
|
Re:chipped my ECU ..Problems...!!!!
sorry bout that..its the PM6 ECU..i am using the hack with the PG7 right now cause of the problems.
|
Re:chipped my ECU ..Problems...!!!!
Along the sides of the PM6, there are electrical components secured to the sides of the cases. In a good ECU there are rubber insulators between these components and the metal case. When people chip ECUs sometimes (and dont know what they are doing) they take the entire board out of the cases and these rubber pieces fall out or get misaligned. This would cause these pieces to no longer be insulated.
Check that out...if you find what I am describing, just put a piece of thin plastic behind them and them tighten the screws down. |
Re:chipped my ECU ..Problems...!!!!
Originally Posted by julio_bOOstamante
I tried using the .bin that Chevy wrote for me and it wont go past 3,500 RPM's. I tried the one i made and it wouldnt go past 4,000 k. I did notice thought that when i held the gas and it would just stop at 4,000 it would blow off abit when i let off the gas.
Anyway, i also noticed that when the ECU case touched the metal on the car ( the mouting area where the ECU sits ) it would cut off. Like somethin isnt grounded within the ECU. I can't seem to figure it out. I dont know whats causing the short and i'm thinking that this is why it wont rev past 4,000k. anyone ever have this problem. thats called full throttle lanch (sp) |
Re:chipped my ECU ..Problems...!!!!
thats what i was gonna say... take it for a spin around the block julio... 4k rpm at idle is the launch controler... do that at a stop light then pop the clutch lol... enjoy
oh yah... gimme my damn wire cutters back... u theif |
Re:chipped my ECU ..Problems...!!!!
Originally Posted by turboDA6
oh yah... gimme my damn wire cutters back... u theif |
Re:chipped my ECU ..Problems...!!!!
Originally Posted by xenocron
When people chip ECUs sometimes (and dont know what they are doing)
|
Re:chipped my ECU ..Problems...!!!!
Originally Posted by chevy
Originally Posted by julio_bOOstamante
I tried using the .bin that Chevy wrote for me and it wont go past 3,500 RPM's. I tried the one i made and it wouldnt go past 4,000 k. I did notice thought that when i held the gas and it would just stop at 4,000 it would blow off abit when i let off the gas.
Anyway, i also noticed that when the ECU case touched the metal on the car ( the mouting area where the ECU sits ) it would cut off. Like somethin isnt grounded within the ECU. I can't seem to figure it out. I dont know whats causing the short and i'm thinking that this is why it wont rev past 4,000k. anyone ever have this problem. thats called full throttle lanch (sp) interesting Quote from: turboDA6 on September 27, 2004, 10:44:37 PM oh yah... gimme my damn wire cutters back... u theif told ya he was mexican i didnt notice till today that i had them..i'll give em back dont worry! Posted by: xenocron Posted on: September 27, 2004, 05:16:30 PM Along the sides of the PM6, there are electrical components secured to the sides of the cases. In a good ECU there are rubber insulators between these components and the metal case. When people chip ECUs sometimes (and dont know what they are doing) they take the entire board out of the cases and these rubber pieces fall out or get misaligned. This would cause these pieces to no longer be insulated. Check that out...if you find what I am describing, just put a piece of thin plastic behind them and them tighten the screws down. thanks again! |
Re:chipped my ECU ..Problems...!!!!
hahaha LMAO....A lot of people don't get what the launch control is lately.
|
Re:chipped my ECU ..Problems...!!!!
Originally Posted by Semnos
hahaha LMAO....A lot of people don't get what the launch control is lately.
whanks a millions you guys! |
Re:chipped my ECU ..Problems...!!!!
it goes away after 8mph... till then jus keep ur foot to the floor lol
|
Re:chipped my ECU ..Problems...!!!!
i didnt nkow that...thats ------- sweet!
now all i need to do is go try it! |
Re:chipped my ECU ..Problems...!!!!
Originally Posted by xenocron
Along the sides of the PM6, there are electrical components secured to the sides of the cases. In a good ECU there are rubber insulators between these components and the metal case. When people chip ECUs sometimes (and dont know what they are doing) they take the entire board out of the cases and these rubber pieces fall out or get misaligned. This would cause these pieces to no longer be insulated.
Check that out...if you find what I am describing, just put a piece of thin plastic behind them and them tighten the screws down. Fixed it today ..actually just now and took it for a spin.... works ------- great! Thanks to you ann especially CHEVY for hooking me up with that Bin!!!!!!! Launch control is awsome and it runs awsome.....i hit 10psi in 2nd and 6 in 1st i let off cause i was on a busy street and i have a waarant so i dont want to go to jail anytime soon.. |
Re:chipped my ECU ..Problems...!!!!
Originally Posted by julio_bOOstamante
Originally Posted by xenocron
Along the sides of the PM6, there are electrical components secured to the sides of the cases. In a good ECU there are rubber insulators between these components and the metal case. When people chip ECUs sometimes (and dont know what they are doing) they take the entire board out of the cases and these rubber pieces fall out or get misaligned. This would cause these pieces to no longer be insulated.
Check that out...if you find what I am describing, just put a piece of thin plastic behind them and them tighten the screws down. Fixed it today ..actually just now and took it for a spin.... works ------- great! Thanks to you ann especially CHEVY for hooking me up with that Bin!!!!!!! Launch control is awsome and it runs awsome.....i hit 10psi in 2nd and 6 in 1st i let off cause i was on a busy street and i have a waarant so i dont want to go to jail anytime soon.. let me no if u would like me to edit something on the map let me no |
Re:chipped my ECU ..Problems...!!!!
haha, you have a warrent. everybody in new mexico has a warrant for one little stupid thing or another.
|
Re:chipped my ECU ..Problems...!!!!
ill hit you up for a bin when i get some 450's CHevy....
and y es warrants suck! |
All times are GMT -5. The time now is 01:24 PM. |
© 2024 MH Sub I, LLC dba Internet Brands