Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

Car will not start

Old 06-03-2005, 11:10 PM
  #1  
0.5 BAR
Thread Starter
 
Join Date: Apr 2005
Posts: 82
Default Car will not start

I just finished my turbo project, and my car will not start. I am useing uberdata and 450cc injectors from tunertoys. I think that I am getting to much fuel when i try to start. I am trying to burn a new base map but i cant figue out how to save so it can be burned on my burn1. Any trouble shooting idea's would help.
irocz is offline  
Old 06-04-2005, 02:15 AM
  #2  
0.5 BAR
Thread Starter
 
Join Date: Apr 2005
Posts: 82
Default Re: Car will not start

I just found out i have no spark. I probably disconected something during the installation. I gotta find were now.
irocz is offline  
Old 06-04-2005, 09:41 AM
  #3  
3.0 BAR
 
Join Date: Mar 2003
Posts: 5,285
Default Re: Car will not start

Yeah, check out all your plug wires and the plugs on the distributor. You had no reason to remove the timing belt or anything like that correct? Just curious to know if the timing's still set correctly.
tranceminister is offline  
Old 06-06-2005, 11:06 PM
  #4  
0.5 BAR
Thread Starter
 
Join Date: Apr 2005
Posts: 82
Default Re: Car will not start

I will double check the plug wires. I did not have to remove the timming belt at all. I did do some unnessary cutting an soldering will i was installing my w/b o2 sensor. I will double check that as well. But my car ran fine after i installed the wideband.
irocz is offline  
Old 06-07-2005, 04:43 PM
  #5  
3.0 BAR
 
Join Date: Mar 2003
Posts: 5,285
Default Re: Car will not start

Unnecissary cutting like what? It may have run after the wideband install but when you installed the turbo setup maybe a wire got loosened up ir something.
tranceminister is offline  
Old 06-11-2005, 02:11 AM
  #6  
0.5 BAR
Thread Starter
 
Join Date: Apr 2005
Posts: 82
Default Re: Car will not start

When i was looking for a switch 12 volt source i tryed 2 different wires that did not work. Then i found a pin out chart on the plx devices web site and found a good switch 12v. I have to go check my wiring agin. It is hard to explane all the wiring i did.
irocz is offline  
Old 06-14-2005, 06:04 PM
  #7  
0.5 BAR
Thread Starter
 
Join Date: Apr 2005
Posts: 82
Default Re: Car will not start

I think i figured out what went wrong. When i install my wbo2 sensor(plxm300) I concted my o2 heater wire with the resistores to the black and yellow wire on my distrurator, and that is the 12 power sorce for the ignitor. So i am thinking that it burned out the ignitor. I sould have conected the 02 heater wire the the sensor ground wire if im not mistaken, it is wht and grn pin d22. What adum mistake. Hopefully I can change the ignitor and it will stat up.
irocz is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Donald125
Turbo Parts For Sale
1
05-18-2007 11:23 PM
Turblow
Fabrication
33
11-13-2006 09:19 PM
AgentMurdoc
Turbo Parts For Sale
4
11-06-2005 12:38 PM
hybrdcivic95
General Discussion
1
11-07-2004 09:09 PM


Thread Tools
Search this Thread
Quick Reply: Car will not start


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.