1.8 to 2.5 Changeover?
Well it just came in the mail. My 2.5bar MAP sensor from Digikey. Although it isn;t nessecary yet, I fiqured I play with it for a little before be build.
My question is I have a fairly nice tune in my NG60 TE 1.8 Bar. But is there any way of changing the tune from 1.8bar to 2.5 without starting all over agian? Is there an conversion equation? I know if there is I will have to return for 11.3pis, but heck at this point I wont be any higher then 12psi. |
Re: 1.8 to 2.5 Changeover?
Anyone?
|
Re: 1.8 to 2.5 Changeover?
yes, you'll still have to retune ;)
|
Re: 1.8 to 2.5 Changeover?
But do I have to make a whole new Basemap using lets say the basemap helper, do mulitple pulls with the WB02 to fiqure out the ideal AFR and then play around with my timing seeing as thathas changed also, or is the a formula that I can apply to my Cells to get my previously tuned map, Fairly close to where I want it and then do an hour or so of fine tuning?
|
Re: 1.8 to 2.5 Changeover?
Always ends up way lean on any car i have done
def need to retune |
Re: 1.8 to 2.5 Changeover?
K. How do I go about setting up a basemap. I use a your ------sheet for the NG55 code. Create the map off ofthat using a NG60-1.8bar ROM with the options changed to 2.5 map. Didn't run. it started but no idle and need gas to keep it up. The only other map I found was the NG55-2.5bar map. I got the samething out of that.
|
Re: 1.8 to 2.5 Changeover?
if you are using my ancient basemapper...i would just keep adding fuel using the 'Tweak' until you get it to start
are you using an Ostrich and the new NG60 code though? |
Re: 1.8 to 2.5 Changeover?
Nope, just NG60, Moates Burn1, and SST chips.
Why? What is with Ostrich? |
Re: 1.8 to 2.5 Changeover?
Originally Posted by bumblezc
Nope, just NG60, Moates Burn1, and SST chips.
Why? What is with Ostrich? It allows you to tune in real time and is supported by TurboEdit, Crome and Uberdata. Really, you havent heard of it??? |
Re: 1.8 to 2.5 Changeover?
You can use my 2.5bar ng60 map that is up on Xeno's site. It should provide a good start point.
|
Re: 1.8 to 2.5 Changeover?
Originally Posted by xenocron
Originally Posted by bumblezc
Nope, just NG60, Moates Burn1, and SST chips.
Why? What is with Ostrich? It allows you to tune in real time and is supported by TurboEdit, Crome and Uberdata. Really, you havent heard of it??? |
Re: 1.8 to 2.5 Changeover?
Oh...no relation really. Its just the fuel 'curve' remains the same generally. You should be able to do very global changes to your old maps to synch them between the map sensors...using the Ostrich and doing it in real time shows this and makes for much quicker and easier tuning in my opinion.
|
Re: 1.8 to 2.5 Changeover?
Ya, I would luv Real TIme, but I burn basic Stock maps for some guys with swaps locally, and still need a basic burner. Maybe next season I maybe running Real TIme when I really could benifit from it.
|
All times are GMT -5. The time now is 08:42 AM. |
© 2024 MH Sub I, LLC dba Internet Brands