Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

***Basemap won't work need expert help***

Old 02-24-2006, 12:45 AM
  #1  
0.5 BAR
Thread Starter
 
Join Date: Jan 2005
Posts: 192
Default ***Basemap won't work need expert help***

Everytime I burn a map and put it in my civic (d16z6) the check engine light comes on. I check to see what code it's throwing but it isn't showing any codes (no blinking). What's weird is that when I disconnect the jumper to the base map the check engine light goes away. So I thought it was the ecu but I put in my po5 vtec converted and chipped ecu and it does the same thing. I've burnt basemaps on cromepro and uberdata but the same thing happens. Another thing I found wierd was that there's a buzzing noise comming from the black thing behind the throttle body (near the butterfly) when I connect the basemap to the ecu. Then when I take the jumper to the basemap out it goes away. This is my second setup and I haven't run into this problem before. Please... anyone who's run into the same problem or knows what's going on help a fellow HMT member out thanks.
Type-X is offline  
Old 02-24-2006, 01:41 AM
  #2  
3.0 BAR
 
Join Date: Dec 2002
Posts: 3,832
Default Re: ***Basemap won't work need expert help***

When I run into these problems, I like to start off with a massive sensor disable base map hahahah
Disable every last sensor in CROME and see if it works. If it does, start adding them back in one by one.
Also, on your CROME map, did you disable the checksum?

The buzzing sounds like its coming from your IACV, and w/ key on that should be normal IIRC.

leed is offline  
Old 02-24-2006, 01:20 PM
  #3  
0.5 BAR
Thread Starter
 
Join Date: Jan 2005
Posts: 192
Default Re: ***Basemap won't work need expert help***

Originally Posted by leed
When I run into these problems, I like to start off with a massive sensor disable base map hahahah
Disable every last sensor in CROME and see if it works. If it does, start adding them back in one by one.
Also, on your CROME map, did you disable the checksum?

The buzzing sounds like its coming from your IACV, and w/ key on that should be normal IIRC.

Yeah I disabled checksum. But if I disable all sensors would the car even start at all. But it's worth a try. I'll check up on that. Here's my setup:
Setup:
-d16z6 (stock)
-t3/t4
-460cc injectors w/ 10 ohm resistors
-7psi
-2.5 charge pipes
-intercooled
-chipped ecu
Don't know how to post up bin so I'll e-mail it to anyone who's willing to help thanks.
Type-X is offline  
Old 02-24-2006, 01:34 PM
  #4  
0.0 BAR
 
Join Date: Mar 2003
Posts: 0
Default Re: ***Basemap won't work need expert help***

everytime i get the "buzzing form the black thing" and a solid CEL it is usually a bad burn. what burner are you using and has your ecu had a chip in it since it has been chipped without throwing a CEL and buzzing?
J-MAN is offline  
Old 02-24-2006, 02:41 PM
  #5  
0.5 BAR
Thread Starter
 
Join Date: Jan 2005
Posts: 192
Default Re: ***Basemap won't work need expert help***

Originally Posted by jeffsciv23
everytime i get the "buzzing form the black thing" and a solid CEL it is usually a bad burn. what burner are you using and has your ecu had a chip in it since it has been chipped without throwing a CEL and buzzing?
I think it's my willem burner. I was looking at it and one of the components fell out. I'm trying to solder it in right now but I hope that's the problem.
Type-X is offline  
Old 02-24-2006, 03:23 PM
  #6  
0.5 BAR
Thread Starter
 
Join Date: Jan 2005
Posts: 192
Default Re: ***Basemap won't work need expert help***

I sodered that peice back in but still same issue. When I burn I ussually get error codes like: error at 0x000000 Chip = 0xFF buffer = 0xED or
0x000000 Chip = 0xFF buffer = 0xE2 Don't know what these mean. I erased the chip moved/removed the jumper to burn and still i get that. After like the 5th or 6th try it'll let me burn a map. I tried disableing all my sensors on crome but i still get a solid cel.
Type-X is offline  
Old 02-24-2006, 07:05 PM
  #7  
0.0 BAR
 
Join Date: Mar 2003
Posts: 0
Default Re: ***Basemap won't work need expert help***

yeah it's your burner not burning right. are you using an offset with your burn?
J-MAN is offline  
Old 02-25-2006, 03:02 AM
  #8  
0.5 BAR
Thread Starter
 
Join Date: Jan 2005
Posts: 192
Default Re: ***Basemap won't work need expert help***

never mind got it to work. Don't know how but thanks for all the help guys.
Type-X is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Minor Threat
Engine Management
6
04-10-2006 12:11 AM
92HondaEX
Forced Induction
2
01-01-2006 07:47 PM
juli0_bustamante
Engine Management
4
06-27-2005 04:48 PM
topspeed
Engine Management
10
04-02-2005 11:12 PM
teamlegacy
Forced Induction
7
09-13-2003 04:22 PM


Thread Tools
Search this Thread
Quick Reply: ***Basemap won't work need expert help***


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.