crx project v1.154345
08-09-2007, 08:02 PM
#61
3.0 BAR
Thread Starter
Join Date: Oct 2005
Posts: 9,282
Re: crx project v1.154345
good deals? how much should i counter offer
CRX or civic Koni Yellows with H & R Lowering Springs $400
CRX or Civic BNIB Tokico Blues. $200.
if this engine fails to start i will either go b16 or b18
but aall seems promising since it manually turned over from the dampner pully or w/e itss called
CRX or civic Koni Yellows with H & R Lowering Springs $400
CRX or Civic BNIB Tokico Blues. $200.
if this engine fails to start i will either go b16 or b18
but aall seems promising since it manually turned over from the dampner pully or w/e itss called
08-09-2007, 08:24 PM
#62
3.0 BAR
Join Date: Mar 2003
Posts: 21,479
Re: crx project v1.154345
Put your purse down and push that axle in the tranny. Sometimes they take some pressure. Get it to where the splines line up and ram that **** in there.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
08-09-2007, 09:20 PM
#64
0.0 BAR
Join Date: Feb 2003
Posts: 0
Re: crx project v1.154345
Koni Yellows are nice, and rebuildable, but you might want to pass on those because at that price with that appearance they need rebuilt.
Tokico Blues = stockers.
Be careful to NOT pull the inner axle joint out as they are a PITA to reset. Push the axle as far in as it will go and then smack the other end of the axle with a hammer... use a rubber/brass/plastic deadblow hammer to keep the end of the axle from mushrooming, or put a piece of wood across the nose of it and use a normal hammer. The axle should click into place with one good whack... if it doesn't seat fully it'll be prone to popping back out.
Was it a fair trade for Yuriy's tools?
Tokico Blues = stockers.
Be careful to NOT pull the inner axle joint out as they are a PITA to reset. Push the axle as far in as it will go and then smack the other end of the axle with a hammer... use a rubber/brass/plastic deadblow hammer to keep the end of the axle from mushrooming, or put a piece of wood across the nose of it and use a normal hammer. The axle should click into place with one good whack... if it doesn't seat fully it'll be prone to popping back out.
Was it a fair trade for Yuriy's tools?
08-09-2007, 09:32 PM
#65
3.0 BAR
Thread Starter
Join Date: Oct 2005
Posts: 9,282
Re: crx project v1.154345
Originally Posted by Joseph Davis
Koni Yellows are nice, and rebuildable, but you might want to pass on those because at that price with that appearance they need rebuilt.
Tokico Blues = stockers.
Be careful to NOT pull the inner axle joint out as they are a PITA to reset. Push the axle as far in as it will go and then smack the other end of the axle with a hammer... use a rubber/brass/plastic deadblow hammer to keep the end of the axle from mushrooming, or put a piece of wood across the nose of it and use a normal hammer. The axle should click into place with one good whack... if it doesn't seat fully it'll be prone to popping back out.
Was it a fair trade for Yuriy's tools?
Tokico Blues = stockers.
Be careful to NOT pull the inner axle joint out as they are a PITA to reset. Push the axle as far in as it will go and then smack the other end of the axle with a hammer... use a rubber/brass/plastic deadblow hammer to keep the end of the axle from mushrooming, or put a piece of wood across the nose of it and use a normal hammer. The axle should click into place with one good whack... if it doesn't seat fully it'll be prone to popping back out.
Was it a fair trade for Yuriy's tools?
fair trade for yuriys tools? idk.. the hard drive was a 200gb ffull of all my ----.. and the nitro rc car was brand new not even a half gallon of nitro ran through it.. all it needed was an 18 dollar starter coil because i ran it too rich for break in.. got oil on the one way bearing.. had to clean it and the coil unsprung.. meh
his tools werent worth ----.. and his fuel pump is annoyingly loud tools + 200 i owed him = fair trade..yuriy is a ******, and time will tell, he knows i was a good friend.. but he fucked it up because hed rather make fun of me infront of his other friends than introduce me.. anyways.. this isnt about that..
tomorrow im getting the other side of the axle and suspension in and im gonna take as manny pictures as i can.. i wish i had a decent camera...
http://cgi.ebay.com/ebaymotors/Unive...spagenameZWDVW
that seems like a good deal.. is it?
08-09-2007, 09:45 PM
#66
0.0 BAR
Join Date: Feb 2003
Posts: 0
Re: crx project v1.154345
Originally Posted by buk9tp
yuriy is a ******, and time will tell, he knows i was a good friend.. but he fucked it up because hed rather make fun of me infront of his other friends than introduce me.. anyways.. this isnt about that..
Given the way you harrass MR2 Gurl, the whole situation with Urine-y, etc, I'm not surprised no one is willing to intro you to friends or help you for money, I don't doubt for a second you're a nice guy but you don't understand, as rawr stated, personal boundaries.
Now, back to just tech, hmm?
08-09-2007, 10:27 PM
#67
3.0 BAR
Thread Starter
Join Date: Oct 2005
Posts: 9,282
Re: crx project v1.154345
the mr2 gurl thing is a joke, i knew it was gonna come back to you which is why i did it
i dont think ive talked to anyone on hmt seriously other than caleb a couple times.. everyone else ive just fucked with..
yes just tech...
is that battery relocation kit a good deal
i dont think ive talked to anyone on hmt seriously other than caleb a couple times.. everyone else ive just fucked with..
yes just tech...
is that battery relocation kit a good deal
